voluting造句

• volute mixed flow pump-part 2 : requirements
  蜗壳式混流泵.第2部分:技术条件
• volute mixed flow pumps-part 1 : types and basic parameters
  蜗壳式混流泵.第1部分:型式与基本参数
• Benz engine oil level volute
  奔驰引擎机油油尺奔驰引擎机油油尺
• Double suction volute pumps
  双吸螺旋泵
• Bogie volute spring
  转向架锥形弹簧
• Numerical simulation of flow field in the double volute of hd type petrol-chemical process pump
  型石油化工流程泵双蜗壳内部流场数值计算
• Numerical investigation on the swirling flow inside a volute influenced by distorted inflow
  离心风机蜗壳进口周向来流的非均匀性对其旋涡流动影响的数值研究
• In the second part, in terms of the youth actualities, to talk about the effect on the volute of the youth
  第二部分，结合青年思想的实际情况，具体论述大众文化对青年身心健康的影响。
• This paper is about the experiment and numeric simulation of the metalwork impact on the volute vane of the particle separator
  与此同时,带来的影响是粒子分离器本身可能受沙石和硬物的撞击,其强度与寿命将受到很大影响。
• It is based on the application of explicit finite element ( fe ) analysis codes to study volute vane behavior under metalwork impact conditions
  根据实际叶片的特点设计了叶片金属块撞击的试验件,按照不同的条件进行了撞击试验。
• Suitable for producing double twist spring, straight spring, pagoda-shaped draught spring, rectangular spring, wires with various shapes, volute spring and other special-shaped springs
  五、适用于生产双扭簧、直形簧、宝塔拉簧、矩形簧、线材成形、钢皮涡簧及各种花式簧、异形簧等。
• Sow series single stage double entry pump is a horizontally split volute centrifugal pump, mainly used to handle clean water or liquids similar to water in physical and chemical properties, temperature not above 105
  sow系列单级双吸泵系水平中开蜗壳式离心泵，主要供输送温度不高于105的清水或理化性质类似于水的液体。
• Then a specific ventilator was chosen as an example, and by the method of objective functions, the diffusion angle of its volute was calculated and analysed to optimize the operating performance of the ventilator
  并针对有具体用途（使通风机的流量达到额定值）的通风机，采用目标函数法对通风机综合性能指标最优化的扩压角进行了算例分析。
• The base discharge elbow shall meet the slide bracket by method of a three point, wedged engagement that is uniquely designed to match the volute flange to the stationary elbow to eliminate head losses
  排泄弯头基座应该与滑动平台相匹配，所采用的连接方式应该为三点楔入接合式，并专为蜗形法兰与固定弯头特别设计，能够达到消除扬程损失的目的。
• By the multiple objective optimization, the diffusion angle of the ventilator volutes with high efficiency, low noise and high total pressure of the ventilators was calculated and selected according to the experimental data
  摘要根据实验数据，采用多目标最优化的方法，对效率高、噪声小、全压大等性能指标皆好的通风机蜗壳扩压角进行了理论计算选择。
• Although the structure of the pump is different from the normal one, the performance of the pump can be measured and the internal flow fields in the volute and impellers can be investigated by using piv easily
  这样，该实验装置既能进行水泵性能试验，又满足piv的测试要求。本文在转速为1200r/min工况下，进行了水泵的外特性试验，得到了水泵的性能曲线。
• The velocity-coefficient method was used to design a 180mm diameter impeller with five single-arc-cylinder blades . the exit angle and inlet angle of the segment are 35.1 and 36.0 in degrees respectively . the shape volute's cross-section is the rectangle
  该叶轮采用速度系数法设计，转轮外径180mm，共有5张单圆弧圆柱形叶片，其出口安放角、进口安放角分别为35.1度、36.0度。
• It requires more even airflow and avoids the tremble of the compressor and the instability of gas turbine . at the same time, the dimension of the inlet volute must be as small as possible, so that the gas turbine can work well
  一方面，它要求流经进气蜗壳的气流尽量均匀，以免造成压气机的喘振和整个动力装置性能的不稳定；另一方面，要求进气蜗壳结构尺寸在保证要求的前提下尽量小，有利于机舱的布置。
• In the first part, the method of velocity coefficient was used to design a 100mm diameter impeller with five single-arc-cylinder blades, and the method of velocity moment was applied to design the volute " s cross-section . the volute " s cross-section is a rectangle, which was designed as a whole structure with the front shroud of the pump . a special lighting window was designed on the side
  在第一部分工作中，设计了一个带半开式叶轮的微型泵：叶轮外径100mm、共5片单圆弧圆柱形叶片；蜗壳采用速度矩法设计，内为矩形断面，和泵壳前盖板为一整体、透明结构，侧面专门设计一个打光窗口。
• In the first part, the method of velocity coefficient was used to design a 100mm diameter impeller with five single-arc-cylinder blades, and the method of velocity moment was applied to design the volute " s cross-section . the volute " s cross-section is a rectangle, which was designed as a whole structure with the front shroud of the pump . a special lighting window was designed on the side
  在第一部分工作中，设计了一个带半开式叶轮的微型泵：叶轮外径100mm、共5片单圆弧圆柱形叶片；蜗壳采用速度矩法设计，内为矩形断面，和泵壳前盖板为一整体、透明结构，侧面专门设计一个打光窗口。