压制压力的英文

• pressing pressure

• "压制"英文翻译    suppress; stifle; inhibit; r ...
• "压力"英文翻译    pressure; tension
• "单位压制压力" 英文翻译 :    specific molding pressure
• "调制压力" 英文翻译 :    modulated pre ure; modulated pressure
• "绘制压力图" 英文翻译 :    pressure plotting
• "控制压力" 英文翻译 :    command pressure; control pressure; operating pressure; pilot pressure
• "模制压力" 英文翻译 :    molding pressure
• "轧制压力" 英文翻译 :    draught pressure; pressure of rolling; roll pressure; rolling pre ure; rolling pressure
• "钢制压力容器" 英文翻译 :    steel pressure vessels
• "平均轧制压力" 英文翻译 :    average roll pressure
• "真空调制压力" 英文翻译 :    vacuum modulator pre ure; vacuum modulator pressure
• "控制压力挤出法" 英文翻译 :    controlled pressure extrusion
• "控制压力完井法" 英文翻译 :    controlled pressure completion
• "平均轧制压力速率" 英文翻译 :    average roll pressure
• "压力机压制" 英文翻译 :    press compacting
• "制压" 英文翻译 :    [军事] neutralize◇制压射击 [军事] neutralization fire
• "施加压力压制" 英文翻译 :    clamdown on they clamdown on the newspapers
• "强度调制压力传感器" 英文翻译 :    intensity-modulated presure sensor
• "模压制模压力机" 英文翻译 :    die hobbing press
• "钢制压力弯头的极限抗弯能力及挠度" 英文翻译 :    ultimate bending capacity and buckling of pressurized deg steel elbows
• "自动控制压力蒸汽灭菌器技术条件" 英文翻译 :    specifications for automated autoclave sterilizer
• "压制" 英文翻译 :    1.(强力限制) suppress; stifle; inhibit; repress 压制合理化建议 smother reasonable suggestions; 压制群众的意见 stifle the opinions of the masses; 压制批评 suppress [muzzle] criticism; 压制火力 [军事] subjugate fire; 压制新生力量 hold back new rising forces2.[机械工程] (用压的方法制造) pressing; calendering; 压制板 pressboard; 压制玻璃 [材料] pressed glass; 压制唱片 pressing; 压制成型 compression moulding; 压制钢板 pressed-steel plate; 压制射击 controlled shooting
• "压力加工 压制成品 冲压成品 印刷作业" 英文翻译 :    presswork
• "调制压缩" 英文翻译 :    modulation compression
• "调制压缩度" 英文翻译 :    degree of modulation compression

• Dense lsco ceramic targets without cracks were prepared with cobalt nitrate excess coefficient 1 . 05 and pressing pressure 8mp , sintered at 1350 for 3h . the xrd spectrum is consistent with the standard cards of lsco powder
  通过大量实验,确定了最佳烧结工艺:烧结温度为1350 、保温3小时,硝酸钴过量系数为1 . 05 ,压制压力为8mp 。
• We analyze the microstrain and density changing of the composite powders during pressing . the density evolution of ti / al composite billet became calm when the pressure get to 1000mp . the technique of vacuum degassing can reduce the content of atmosphere
  分析了复合粉在冷压制过程中的微观变形过程,不同压力下的密度变化趋势,表明在冷压制压力达到1000mpa后复合粉预制坯密度变化趋于平稳。
• The studies indicated that the rigidity of the copper billet was enhanced a lot with different pressure and different forms of pressure , and by the obvertion of the microscopic structure , we find that the aluminizing formations had different thickness with different pressure
  研究结果表明：对不同压制压力下及不同压制方式的纯铜渗铝后，铜坯的硬度得到很大的提高，对显微组织观察可知，在不同压力下渗铝其渗层厚度明显不同。
• By analyzing microstructure and morphology of the composites at the different pressure and different sintering temperature , optimal craft parameters of primary pressing - sintering were ascertained : 350mpa ( pressing ) + 400 c + lh ( clearing gas ) + 800 c + 40min ( sintering ) . after primary press , the carbon fibers showed some directional distribution
  通过对比不同压制压力和烧结温度下复合材料的显微组织形貌，确定初压烧结的最佳工艺参数为： 350mpa压制+ 400 1h除气+ 800 40min烧结。初压后，碳纤维在基体中的分布产生了一定的取向性。
• Remarkably , the temperature must be limited between softening point and solidification value , at which the bond can get perfect fluidity and stickiness . effects of bond content and pressure on magnet product during heating - pressing process are the same with effects during common - pressing process . fourthly , it is more than 250 hours before magnet is eroded when it is coated with lacquer by way of cathode electrophoresis
  温度对温压效果影响明显，应当选择在粘结剂软化点以上、固化反应前的某一点，保证粘结剂具有适当的粘度和良好的流动性；与普通压制工艺相同，温压工艺制备的粘结磁体密度和磁性能均随压制压力的增大而提高，磁体性能和磁粉体积分数随粘结剂含量变化的规律一致。
• The experiment is about researching the permeated aluminum technology process of pure copper , the characteristic of permeating cover and the thoery of forming permeating cover ， to measure the hardness of the permeated pure copper and make an observation on microcosmic organization , compare the permeating cover under different thrust pressure
  本实验对纯铜的渗铝工艺过程、渗层的组织特征以及渗层的形成机理进行了研究；对纯铜渗后试样进行了硬度测试和微观组织的观察，并对不同压制压力下得到的渗层进行了比较