前向通道的英文

• forward path

• "前"英文翻译    front
• "向"英文翻译    direction
• "通道"英文翻译    thoroughfare; passageway; pa ...
• "正向信道 前向信道 单向通道" 英文翻译 :    forwardchannel
• "前向通量密度" 英文翻译 :    forward flux density
• "前向通信中心" 英文翻译 :    forward communication center
• "正向通路, 前向路" 英文翻译 :    forward path
• "半双向通道" 英文翻译 :    half duplex cha el; half duplex channel; half-duplex channel
• "单向通道" 英文翻译 :    forward channel; half duplex channel; half-duplex channel; one way channel; one-way channel; one-way only channel; simplex channel
• "反向通道" 英文翻译 :    reverse channel
• "横向通道" 英文翻译 :    interconnection
• "快内向通道" 英文翻译 :    fast inward channel
• "慢内向通道" 英文翻译 :    slow inward channel
• "竖向通道" 英文翻译 :    vertical passageway
• "双向通道" 英文翻译 :    both way channel; duplex cha el; duplex channel; two-way channel; two-wire channel
• "有向通道" 英文翻译 :    directed walk
• "正向通道" 英文翻译 :    forward cha el; forward channel
• "只单向通道" 英文翻译 :    one way only channel
• "轴向通道" 英文翻译 :    axial channel; axial passage
• "纵向通道" 英文翻译 :    fore-and-aft gangway
• "前向性通道" 英文翻译 :    antegrade pathway
• "磁泡导向通道" 英文翻译 :    bubble guide channel
• "开式有向通道" 英文翻译 :    open directed walk
• "同时双向通道" 英文翻译 :    full-duplex channel
• "远程轴向通道" 英文翻译 :    raa

• The effect of the gain in forward channel on the stability and result of control scheme have also been illustrated by numerical simulation
  文中还通过仿真算例分析了系统前向通道增益对控制稳定性和控制结果的影响。
• But , the former is not so easy , especially the anomalous plane . this paper plans to design a planimeter to solute this problem
  本系统设计至少要包括单片机存储器及i o扩展，人机通道，前向通道及后向通道的的软硬件设计。
• The influences of the driving error and hysterisis error to the closed servo system were analyzed and their calculation methods have been put forward
  分析闭环伺服系统前向通道上精密传动装置的传动误差和回程误差对伺服系统性能的影响，提出计算方法。
• Hardware controller uses the at89c51 monolithic integrated circuit , a / d transformation uses 12 bit transformations chips max187 , has completed the design of a front channel for sampling and processing the simulated signal
  其中硬件单片机采用at89c51单片机, a / d转换采用12位转换芯片max187 ,完成了模拟信号从采样到处理的整个前向通道设计。
• On basis of software engineering , adopts the modular designing method , and makes full use of the functions what the mcu offers , such as a / d function , interrupt function , pwm function , and software timer function
  在系统硬件的设计上，设计了前向通道的信号调理电路、键盘模块、液晶显示模块、大容量存储器、串行通讯以及打印机等模块的驱动电路。
• In the paper the constitution of the testing system in the tilting train is discussed , as well as the design of the front access , the subsystems performing the function of interruption , resetting , saving , communication and debugging
  文中不仅对摆式列车测试系统的组成进行了讨论，并围绕dsp设计了测试系统的前向通道，中断、复位子系统，存储了系统，通信子系统和调试子系统。
• This instrument hopes to control the step - motor regularly , and collects the datum of the distance between the laser sensor and the wall simultaneously , then calculates area according to the theory of triangle , finally sums up all the area and makes the output
  本系统前向通道信号由激光传感器提供，后向通道信号发给步进电机、传感器，由于是旋转式测量，必须控制激光发射信号的通断和步进电机的步距角，否则测出的值是无法计算的。
• The hardware of system is used sensor and signal conditioning circuit to collect the signal and communication with the computer using the pci2013 . for the undulation of temperature and driven current will influence the testing result , they need to be invariableness during testing
  系统硬件以传感器和相应的信号调理电路作为前向通道拾取被测信号,利用基于pci高速总线的pci2013数据采集卡和串口模块实现与计算机的数据传输和命令通讯。